Beha-Amprobe is completing the 2100-Series voltage tester range with the 2100-Delta, a rugged feature rich TRMS voltage tester with current-function

Safety rated up to CAT III 1000 V / CAT IV 600 V, makes it the ideal product for troubleshooting in industrial and commercial environments. 
Use it to check voltage, current, resistance, continuity and frequency, all in one instrument. 
Connect the test probes safely to the top of the housing of the instrument when testing for voltage, giving you an extra hand. 
The 2100-Delta simply checks current up to 200A AC by sliding the fixed jaw around the conductor without the need to break the circuit. 
And like the 2100-Alpha, 2100-Beta and 2100-Gamma the 2100-Delta is naturally equipped with reinforced components for dependable performance, it has an ingress protection degree of IP 64, is built according the voltage (current) tester standard EN 61243-3:2014 and is GS approved.

Functions
• Voltage and polarity test TRMS up to 1000 V AC / 1500 V DC
• Current measurement TRMS up to 200 A AC – perfect tool for maintenance and trouble shoot
• Voltage mode to measure AC / DC voltage down to 1 V
• Single pole phase test to determine the phase conductor
• Continuity test (Rx) to check wiring
• Low resistance indication (L Rx) (<20Ω) – most important tool to check wiring in contactor and relay application without influence of the coils
• Phase rotation indication with two probes – no third hand required. Separate indicators for “Right” and “Left” rotation
• Resistance measurement up to 100 kΩ
• Non contact cable break detector / EF (electric field) to locate the exact position of the fault location of a broken phase conductor
• Frequency measurement up to 800 Hz
• Diode test

The Amprobe LAN-1 Cable Tester is designed for testing opens, shorts and miswired cable installations, and works with various data cables and connectors. This cable tester provides a quick go/no-go LED display of the wiring and connection of item under test. You can either step through the test cable wiring one at a time or have the unit automatically pulse through the pin-outs and display the results.

The Amprobe SM-10-A Sound Meter has been designed to check compliance with safety regulations and perform acoustic analysis by safety engineers, health, industrial and safety offices as well as quality control.

They use two different weighting filters required by the IEC651 and ANSI S1.4 Type 2 for audio filtering. The A weighting is for general noise sound level and the C weighting is for measuring sound level of acoustic material control in various environments (ie 94 dB 1 kHz etc).

The Amprobe SM-20A Sound Meter has been designed to check compliance with safety regulations and perform acoustic analysis by safety engineers, health, industrial and safety offices as well as quality control. The SM-20A offers a PC interface.

They use two different weighting filters required by the IEC651 and ANSI S1.4 Type 2 for audio filtering. The A weighting is for general noise sound level and the C weighting is for measuring sound level of acoustic material control in various environments (ie 94 dB 1  kHz, etc).

The Telaris Multifunction Tester Series offers two models that verify the safety of electrical installations in residential, commercial and industrial applications. The Telaris ProInstall series has been developed to carry out the following safety measurements of electrical installations in accordance with EN 61557 and DIN VDE 0100: Insulation resistance, RCD tests, Low Ohm resistance, Earth ground resistance, Loop impedance, Phase sequence.

• Earth bond resistance measurement with 10 A AC or 0.2 A AC Loop / mains impedance measurement up to 440V
• Display of prospective short circuit current
• Insulation resistance measurement with 250 V to 500 V test voltage (adjustable)
• Residual voltage measurement Display of the discharge voltage / discharge time
• Integrated high-voltage test (can be switched off by means of a key switch)
• Easy operation using the rotary switch and the START/STOP button