Fluke 325 True-rms Clamp Meter

sku Product SKU:  FLK-325

Fluke 325 True RMS Clamp Meter offers big AC/DC features in a small form factor

The Fluke 325 Clamp Meter is the top of the 320 Series Clamp Meters. Designed to perform in the toughest environments and provide noise-free, reliable results, you can trust the 325 to help you confidently diagnose all kinds of electrical problems. It features True RMS measurements, optimized ergonomics, a large backlight display, and a rugged compact design to measure current up to 400 A in tight cable compartments. You can also use it to measure temperature, capacitance, AC/DC current and frequency. Commercial and residential electricians use the 325 to verify the presence of load current, AC voltage, and continuity of circuits, switches, fuses and contacts. Frequency measurements allow checking of portable generators; dc current testing battery backups and solar storage equipment.

The Fluke 325 comes with a two-year warranty and a soft carrying case.

ZAR -1

Fluke 353 True RMS 2000 A Clamp Meter

sku Product SKU:  FLK-353

Versatile and rugged tool for applications with high currents

Confidently take reliable readings with the True RMS, Fluke 353 digital clamp meter; the tools of choice for high current clamp-on amp meter measurement up to 2000 A. The extra-wide jaw easily clamps around large conductors, typically found in high-current applications. The extra rugged design and CAT IV 600 V, CAT III 1000 V ratings add an extra element of user protection when taking high-powered measurements.

Accurate peak measurements can be taken using the in-rush current mode, ideal for motors and inductive loads.

ZAR -1

Fluke 355 True RMS 2000 A Clamp Meter

sku Product SKU:  FLK-355

Versatile and rugged tools for applications with high currents

Confidently take reliable readings with the True RMS, Fluke 355 digital clamp meter the tool of choice for high current clamp-on amp meter measurement up to 2000 A. The extra-wide jaw easily clamps around large conductors, typically found in high-current applications. The extra rugged design and CAT IV 600 V, CAT III 1000 V ratings add an extra element of user protection when taking high-powered measurements.

Accurate peak measurements can be taken using the in-rush current mode, ideal for motors and inductive loads. The 355 also measures voltage and resistance, making this an ideal clamp meter for utilities, electrical contractors and industrial service technicians.

ZAR -1

Fluke 365 Detachable Jaw True-rms AC/DC Clamp Meter

sku Product SKU:  FLK-365

The Fluke 365 is a rugged meter perfect for jobs where access to wires is difficult. The 365’s thin, small jaw is detachable with a flexible lead, which makes gaining access to wires and viewing the display easier than ever. Safety Conformance IEC/EN 61010-1:2001, 600V CAT III

 

	FEATURES AND BENEFITS
	200 A ac and dc current measurement with detachable jaw 600 V ac and dc voltage measurement Detachable jaw makes accessing wires and viewing the display easier Built in flashlight/torch allows for easy illumination and identification of wires CAT III 600 V Compact design fits in your hand and can be used while wearing protective equipment State of the art signal processing allows for use in noisy electrical environments while providing stable readings Large, easy to read, backlight display automatically sets the correct measurement range so you do not need to change switch positions while taking a measurement Three-year warranty Soft carrying case
	Safety conformance IEC/EN 61010-1:2001, CAT III 600 V

What’s the difference between the clamp meter models?

	Fluke-365	Fluke-373	Fluke-374	Fluke-375	Fluke-376	Fluke-381
Measure ac current	200.0 A	600.0 A	600.0 A	600.0 A	999.9 A	999.9 A
Measure ac current via iFlex			2500 A	2500 A	2500 A	2500 A
Measure ac voltage	600.0 V	600.0 V	600.0 V	600.0 V	1000.0 V	1000.0 V
Measure continuity	≤ 30 Ω	≤ 30 Ω	≤ 30 Ω	≤ 30 Ω	≤ 30 Ω	≤ 30 Ω
Measure dc current	200.0		600.0	600.0	999.9	999.9
Measure dc voltage	600.0 V		600.0 V	600.0 V	1000.0 V	1000.0 V
Measure resistance	6,000 Ω	6,000 Ω	6,000 Ω	60k Ω	60k Ω	60k Ω
Measure frequency				500 Hz	500 Hz	500 Hz
Measure inrush			100 mS	100 mS	100 mS	100 mS
Work in poorly lit areas	Backlight	Backlight	Backlight	Backlight	Backlight	Backlight
Measure non-linear loads	True-rms	True-rms	True-rms	True-rms	True-rms	True-rms

ZAR -1

Fluke 368 FC Leakage Current Clamp Meter

sku Product SKU:  FLK-368FC

Reduce downtime – Find leakage currents without taking equipment offline.

The Fluke 368 FC true-rms leakage current clamp meter helps users detect, document, record and compare leakage current readings over time as a means of preventing unplanned downtime, and identifying intermittent GFCI and RCD trips, all without taking equipment off line.

The Fluke 368 FC has a large 40 mm diameter jaw for work with large conductors. The clamp’s jaw is fully shielded to accurately capture very small leakage signals, and to minimize external electromagnetic interference.

The 368 FC also offers wireless data connectivity via Fluke Connect. As part of Fluke Connect — the industry’s largest system of software and more than 40 wireless test tools — the 368 FC allows you to track changes in leakage current over time, helping to identify potential problems before they turn into major failures.

ZAR -1

Fluke 374 FC True-RMS AC/DC Clamp Meter

sku Product SKU:  FLK-374FC

Fluke 374 FC delivers advanced troubleshooting performance and wireless connectivity

The Fluke 374 FC, part of the Fluke Connect family of wireless test tools, delivers the standard features you need for everyday troubleshooting. Measure AC and DC current to 600 A with the fixed jaw clamp or add an optional iFlex® flexible current probe to measure all the way to 2500 A. The large diameter and flexible design of the iFlex probe make it easier to measure around large conductors in tight spaces or to access tightly packed wires. You can also use the 374 FC to measure AC and DC voltage to 1000 V and resistance to 6000 Ω.

Use wireless connectivity to keep a safe distance

The 374 FC is Fluke Connect-enabled to wirelessly transmit results via Bluetooth to Apple and Android devices. That means you can read the results out of the arc flash zone, wearing less PPE. You can even save results to the cloud and create and send reports in email right from the field. Or converse in real-time with ShareLive™ video calls.

Versatile feature set

With True-RMS AC voltage and current measurements, the 374 FC enables you to accurately troubleshoot non-linear signals. And you can log and trend measurements to pinpoint intermittents while you are performing other tasks. The Fluke 374 FC Clamp Meter is the direct replacement for the Fluke 374 Clamp Meter.

Other useful capabilities:

• Compatible with optional TPAK magnetic hanging strap
• Comes with soft carrying case, batteries, and three-year warranty
• Measures capacitance to 1000 µF
• Features CAT III 1000 V, CAT IV 600 V safety rating
• Provides True-RMS voltage and current measurements to accurately measure non-linear signals
• Includes Min/Max/Avg and inrush recording to capture variations automatically
• Runs on two AA alkaline batteries

ZAR -1

Fluke 378FC Clamp Meter

sku Product SKU:  FLK-378FC

Product overview: Fluke 378 FC Non-Contact Voltage True-rms AC/DC Clamp Meter with iFlex

Voltage and current measurements with FieldSense™ technology

The Fluke 378 FC true-rms clamp meter uses FieldSense™ technology to make testing faster and safer, all without contacting a live conductor. You get accurate voltage and current measurements through the clamp jaw. Simply clip the black test lead to any electrical ground, put the clamp jaw around the conductor and see reliable, accurate voltage and current values on the display.

Power quality indicator shows whether a problem is in the equipment or the power line

The 378 FC clamp meter includes a unique PQ function that senses power quality issues automatically. When making FieldSense measurements, the 378 FC will detect and display power quality issues, relating to current, voltage, power factor or any combination of the three. Now you can quickly determine if an upstream supply problem exists, or if there is a downstream equipment problem.

Complete 3-phase measurements in quick, easy steps

• Complete 3-phase voltage and current tests in 3 easy steps
• Full set of phase-to-ground and phase-to-phase values calculated and shown on the meter
• Values are also displayed on your smart phone and saved to the cloud via Fluke Connect software
• Phase rotation auto-calculated and shown on the Fluke Connect software
• No more hand-written notes or complicated math.

Measure extremely high current with iFlex® probe

The included iFlex flexible current probe lets you measure ac current as high as 2500 A. Crowded wiring cabinets and large conductors are easily measured with the iFlex probe.

Easy to see, easy to use with included tools

Your job will get easier when you use the 378 FC clamp meter. The display turns green when a stable FieldSense measurement is detected. Visual Continuity also provides a bright green screen for easy detection of continuity in noisy work areas.

Record, analyze, share results with Fluke Connect® software

With Fluke Connect software you can remotely log, trend and monitor measurements to pinpoint intermittent faults. Fluke Connect also allows you to gather data as the basis for a preventive maintenance program.

• Save measurements to your phone and the Fluke Cloud, for comparison of readings over time.

ZAR -1

Fluke 381 Remote Display True-rms AC/DC Clamp Meter with iFlex

sku Product SKU:  FLK-381

What Once Took Two People, Now Takes One

Now one technician can do jobs that would otherwise require two people. Clamp the Fluke 381 around a conductor, remove the display and walk across the room to operate controls or remove protective equipment, all while watching real-time readings.

The iFlex® Flexible Current Probe (included) expands the measurement range to 2500 A AC while providing increased display flexibility. With a cord that runs 6 feet, you can finally measure those tight spaces, awkward sized conductors and disorganized wires.

ZAR -1

Fluke 393 FC

sku Product SKU:  FLK-393FC

The Fluke 393 FC CAT III 1500 V True-RMS Clamp Meter with iFlex is designed for technicians who work in high voltage dc environments: solar arrays, wind power, electric railways, data centres battery banks for uninterruptible power supplies. The Fluke 393 FC will measure up to 1500 V dc, 1000 V ac, and up to 999.9 A dc or ac through the clamp jaw.  The included iFlex flexible current probe extended ac current measurements up to 2500 amps. This clamp has a thin jaw, giving you access to cables in crowded combiner boxes. Test leads are designed with your work in mind and are also rated to CAT III 1500 V dc.

Other key functions:

• IP54 rated, ideal for work outdoors on solar arrays and wind power systems 
• DC power measurement, showing readings in kVA
• Audio Polarity indicator helps prevent accidental misfires
• Visual Continuity turns to provide a bright green light in the display, ideal when working in dark and noisy environments
• Logging and reporting of test results via Fluke Connect software
• When measuring ac current the included iFlex flexible current probe gives you unparalleled access to cable is tight spaces.  The iFlex probe can be twisted through extremely small spaces and provide accurate current measurements.

The world's first CAT III 1500 V true-RMS clamp meter

ZAR -1

Fluke Ti401 Pro

sku Product SKU:  FLK-Ti401-Pro

Every day you work hard to get the job done. Fluke gets that. For over 70 years, we have worked with people in the industrial trades. We understand that you need thermal imagers that will get the job done; rugged general use, everyday thermal imagers that are easy to use, accurate and create high-quality images. The Fluke Ti401 PRO is exactly this type of camera. It is an ideal camera for certified or uncertified thermographers working in:

• industrial maintenance
• heavy commercial facility maintenance
• commercial building diagnostics

The rugged tool you need to establish and maintain a preventive maintenance program.

• Splash resistant
• Dust resistant
• 2-meter drop tested

Capture more than you’d expect, at a price you wouldn’t

Equipped with a unique combination of 640 x 480 resolution and field of view that offers the flexibility to capture measurements in tight spaces or from a distance, even the novice thermographer can capture images of critical issues before they become failures. This well-priced camera offers the highest resolution in its class along with the best-selling features from Fluke. With temperature measurements up to 650 °C, it is suitable for most industrial environments.

Get the most out of your Ti401 PRO with Fluke Connect™ desktop software. Create professional reports in minutes while efficiently capturing full radiometric data to support your maintenance program.

• Edit and optimize images
• Combine infrared and visible images for simpler analysis
• Create detailed reports
• Organize and search images by asset, severity, and title

ZAR -1

Fluke TiX501 Thermal Camera

sku Product SKU:  FLK-TiX501

Contact us to directly to ensure that you selet the right instrument for your application

Use the high definition thermal camera needed to complete reliability inspections, make industrial maintenance decisions, conduct building diagnostic testing and troubleshooting. Work without strain in awkward or hard-to-reach areas with the articulating screen that rotates 240-degrees. This ergonomic design gives you the flexibility to hold the thermal camera in a position that is comfortable, even when taking images overhead, over, under and around hard to reach targets.

ZAR -1

Fluke MDA-550

sku Product SKU:  FLK-MDA-550

Simplify complex motor-drive troubleshooting with guided test setups and automated drive measurements that provide reliable, repeatable test results.

The Fluke  MDA 550 Motor-Drive Analysers save time and eliminate the hassle of setting up complex measurements, while simplifying the troubleshooting process for variable frequency drives. Simply select a test and the step-by-step guided measurements show you where to make voltage and current connections, while the preset measurement profiles ensure you will capture all the data you need for each critical motor-drive section—from the input to the output, the DC bus, and the motor itself. From basic to advanced measurements, the MDA-500 Series has you covered, and with a built-in report generator you can quickly and easily generate as-found, and as-left reports with confidence.

The  MDA-550 are the ideal portable motor-drive analysis test tools and can help safely locate and troubleshoot typical problems on inverter type motor-drive systems.

• Measure key motor-drive parameters including voltage, current, DC Bus voltage level and AC ripple, voltage and current unbalance and harmonics (MDA-550), voltage modulation, and motor shaft voltage discharges (MDA-550).
• Perform extended harmonics measurements to identify the effects of low and high order harmonics on your electrical power system.
• Conduct guided measurements for motor-drive input, DC bus, drive output, motor input and shaft measurements (MDA-550) with graphical step-by-step voltage and current connection diagrams.
• Use simplified measurement setup with preset measurement profiles to automatically trigger data collection based on the chosen test procedure.
• Create reports quickly and easily that are perfect for documenting troubleshooting and collaborative work with others.
• Measure additional electrical parameters with full 500 MHz oscilloscope, meter and recording capability for complete range of electrical and electronic measurement on industrial systems.

The Fluke MDA-510 and MDA-550 Motor Drive Analyzers use guided test measurements to make analysis easier than ever.

Drive input

Measure input voltage and current to quickly see whether values are within acceptable limits by comparing the variable frequency drive’s (VFD), also known as a variable speed drive (VSD) or adjustable speed drive (ASD), nominal rated voltage to the actual supplied voltage. Then, check the input current to determine if the current is within the maximum rating and the conductors are suitably sized. You can also check whether the harmonic distortion is within an acceptable level by visually inspecting the waveform shape or by viewing the harmonics spectrum screen (MDA-550) with total harmonic distortion and individual harmonics.

Voltage and current unbalance

Check the voltage unbalance at the input terminals of the frequency speed drive so you can ensure the phase unbalance is not too high (> 6-8 %), and that the phase rotation is correct. You can also check the current unbalance, as excessive unbalance may indicate a drive rectifier problem.

Extended harmonic measurements

Excessive harmonics are not just a threat to your rotating machines but also to other equipment connected to the electrical power system. The MDA-550 provides the ability to discover the harmonics of the motor-drive but can also discover the possible effects of inverter switching electronics. The MDA-550 has three harmonic ranges, 1st to 51st Harmonics, 1 to 9 kHz and 9 kHz to 150 kHz giving the ability to detect any harmonic pollution problems.

DC bus

In a motor-drive the conversion of AC to DC inside the drive is critical, having the correct voltage and adequate smoothing with low ripple is required for the best drive performance. High ripple voltage may be an indicator of failed capacitors or incorrect sizing of the connected motor. The record function of the MDA-500 Series can be used to check DC bus performance dynamically in the operating mode while a load is applied.

Drive output

Check the output of the inverter drive focusing both on voltage to frequency ratio (V/F), and voltage modulation. When high V/F ratio measurements are experienced, the motor may overheat. With low V/F ratios, the connected motor may not be able to provide the required torque at the load to sufficiently run the intended process.

Voltage modulation

Measurements of the Pulse Width Modulated signal are used to check for high voltage peaks which can damage motor winding insulation. The rise time or steepness of impulses is indicated by the dV/dt reading (rate of voltage change over time), this should be compared to the motor’s specified insulation. The measurements can also be used to measure switching frequency to identify whether there is a potential issue with electronic switching, or with grounding, where the signal floats up and down.

Motor input

Ensuring that voltage is being supplied at the motor input terminals is key, and the selection of cabling from drive to the motor is critical. Incorrect cabling selection can result in both drive and motor damage due to excessive reflected voltage peaks. Checking that the current present at the terminals is within the motor rating is important as over current condition could cause the motor to run hot, decreasing the life of the stator insulation which can result in the early failure of the motor.

Motor shaft voltage

Voltage pulses from a variable frequency drive can couple from a motor’s stator to its rotor, causing a voltage to appear on the rotor shaft. When this rotor shaft voltage exceeds the insulating capacity of the bearing grease, flashover currents (sparking) can occur, causing pitting and fluting of the motor bearing race, damage that can cause a motor to fail prematurely. The MDA-550 Series analyzers are supplied with carbon fiber brush probe tips that can easily detect the presence of destructive flashover currents, while the impulse amplitude and count of events will enable you to take action before failure occurs. The addition of this accessory and capability of the MDA-550 allows you to discover potential damage without investing in expensive permanently installed solutions.

Step-by-step guided measurements ensure you have the data you need, when you need it

The MDA-500 Series is designed to help you quickly and easily test and troubleshoot typical problems on three-phase and single-phase inverter type motor-drive systems. The on-screen information, and step-by-step setup guidance make it easy to configure the analyzer and get the drive measurements you need to make better maintenance decisions, fast. From power input to the installed motor, the MDA-500 provides the measurement capability for the fastest motor-drive troubleshooting.

ZAR -1

Fluke TiX580 Infrared Camera

sku Product SKU:  FLK-TiX580

Contact us to directly to ensure that you selet the right instrument for your application

Does everyone in the plant turn to you? Are you the one who quickly can collect facts, understand issues and mold process and procedures to meet expensive decisions head-on? If so, you need an infrared camera that is as flexible and detail oriented as you are. That is why the TiX580 should always be within arm’s reach. Your day can take you anywhere:

• R&D lab
• Production floor
• Off site, remote locations
• Transmission and distribution lines (substations)

From quality assurance to preventive maintenance and outdoor inspections, everyday can bring a different environment and a different challenge for your thermal imager. With an unsurpassed level of detail in every infrared image and the ability to capture quality images of objects whether they are tiny and close to large and far overhead. The ergonomic design and neck strap make long inspection days easier. Outside the rotating screen lets you adjust to minimize glare and the touchscreen delivers a premium in-field viewing experience. The TiX580 has the tools accommodate your environment.

• Real-time temperature graphs
• Radiometric video recording
• Auto capture image sequence
• MatLab and LabView integration capabilities

Get the most out of your TiX580 with Fluke Connect™ desktop software. Create professional reports in minutes while effic

• Edit and optimize images
• Combine infrared and visible images for simpler analysis
• Create detailed reports
• Organize and search images by asset, severity, and title

ZAR -1

T5-600 Voltage. Continuity and Current Tester

sku Product SKU:  FLK-T5-600

Product overview: Fluke T5-600 Voltage, Continuity and Current Tester

Fluke T5-600 Voltage, Continuity and Current Tester The T5-600 is a versatile troubleshooting tool to carry to every job site. Use it to check voltage, continuity, and current with one compact tool. Just select volts, ohms, or current and the tester does the rest. For higher voltage applications check out the Fluke T5-1000.

Automatically measure AC and DC voltage up to 600 V with precise digital resolution

• Auto-selects between AC and DC voltage
• Suitable for residential or commercial applications

Measure current up to 100 A without breaking the circuit with OpenJaw™ design

• OpenJaw™ design allows for fast and easy current measurement
• Measure current more safely without metallic contact

Troubleshoot resistance problems up to 1000 Ω

• Measure resistance when troubleshooting motors, HVAC systems or electrical systems
• Built-in continuity beeper provides fast and easy go/no-go tests

Work in tight spaces with detachable Slim Reach probe tips

• Features a compact design with handy probe storage, easily fits in one hand
• The test lead slot in the back makes the meter an “extended handle” for the probe, leaving the other hand free to place the second lead
• Test leads accept Fluke accessory test clips

Key safety features

• Protected to EN61010-1 CAT III 600 V rating
• Integrated protection circuit allows it to stay connected to a voltage source longer than a solenoid tester
• UL and CSA approved

Additional product features

• Withstands a 10 ft. (3 m) drop
• Offers Auto-off mode to conserve battery life
• Fits into an optional holster that attaches to a belt and neatly stows test leads

ZAR -1

Fluke DS703 FC Diagnostic Scope

sku Product SKU:  FLK-DS703FC

The Fluke DS703 FC Video Borescope has been updated with improved battery charging and management and can now last up to 4 hours on a single charge.

7” capacitive touch screen for accurate diagnostics in difficult-to-reach spaces. 720p video recording inspection camera. Adjustable LED lighting and digital zoom for quality images. Up is Up® technology rotates the display screen to allow for appropriate image display, regardless of the orientation of the probe. 

Save time with the Fluke Connect® system

Wirelessly sync images directly from your diagnostic scope to the Fluke Connect® system. Having access to maintenance records simultaneously at the inspection site and from the office or an off-site location enables faster decision-making and real-time collaboration between team members.

Expand the flexibility of your video borescope with optional probes offering cameras that range in diameter from 3.8 MM to 8.5 MM, probes as long as 20 meters, and a new camera probe with a 180° degree articulating head. Equip yourself with the right probe for your environment.

ZAR -1

Fluke 705 Loop Calibrator

sku Product SKU:  FLK-705

Fluke 705 loop calibrator provides a cost-effective, integrated solution for calibrating milliamp loops

The Fluke 705 is a cost-effective, integrated solution for calibration, repair and maintenance of milliamp loops. It features a large display and simple, pushbutton interface for ease of use. Plus, it offers the other capabilities you need most to calibrate mA loops including:

• mA sourcing, simulation and measurement
• 0.02% accuracy and 0.001 mA resolution
• Simultaneous mA and % of span display
• Selectable step or ramp outputs
• 24 V Loop supply with mA measure
• 0-28 VDC measurement to check Loop Voltage
• Easy battery exchange without opening the case
• Includes “span check” for fast confirmation of zero and span.
• Provides selectable slow ramp, fast ramp, and step to provide smooth outputs for valve slewing and loop functional tests.
• Includes a 24 volt internal loop supply, so you can power and read a transmitter at the same time without a DMM.
• Runs on a single 9 V battery that is easily changed without breaking the calibration seal
• Offers 0 - 20 mA or 4 - 20 mA default start up modes
• Comes with a protective yellow holster with test lead storage and a three year warranty

And you get all of that in a compact case with a separate protective holster and a three year warranty.

ZAR -1

Fluke 707 Current Loop Calibrator with Quick Click Knob

sku Product SKU:  FLK-707

Fluke 707 Loop Calibrator delivers fast, one-handed, push-button loop checks

The Fluke 707 loop calibrator is a high performance solution for calibration, repair, and maintenance of current loops. It combines the best features of a push-button and knob-base loop calibrator, for extremely fast and easy calibration. The large display and simple quick click rotary button lets you make quick selections and adjustments with one hand. Plus, features such as mA sourcing, simulation, and measurement; simultaneous display of mA and % of span, and selectable step or ramp outputs, helps you work more efficiently and accurately. And you can quickly change the 9V battery without breaking the calibration seal.

ZAR -1

Fluke 709 Precision Loop Calibrator

sku Product SKU:  FLK-709

ZAR -1

Fluke 710

sku Product SKU:  FLK-710

PRODUCT OVERVIEW: FLUKE 710 MA LOOP VALVE TESTER

Smart Control Valve Testing is now easier than ever

The Fluke 710 Valve Testing Loop Calibrator is designed to enable users to perform quick, easy tests on HART smart control valves. Featuring built-in test procedures and an intuitive user interface, the 710 allows users to quickly and easily perform valve tests, while the valve test quick-check results provide at-a-glance diagnostics help you make maintenance decisions faster than ever. The valve health quick-check results let you know whether your valve is in good, marginal or in bad operating condition so you can quickly decide whether additional maintenance is necessary.

Valve testing and HART communication in a precision loop calibrator

With the 710 Valve Testing Loop Calibrator’s built in HART communication function, users can source a 4-20 mA signal to cause the smart control valve to move, while simultaneously interpreting the valve’s HART feedback signal to determine whether the valve is moving to the expected position. In addition to positional information, the measured pressure delivered from the valve’s internal I/P (which moves the valve) can be determined through the HART communication protocol.

The 710 has built-in test procedures that automatically increase and change the mA signal while monitoring the HART position and pressure feedback from the control valve, giving you a better overall picture of valve health at the simple push of a button.

Pre-configured valve tests, at-a-glance answers

Valve test routines built into the 710 include:

• Manual testing; manually change the mA signal and view the HART position and pressure variable information
• Full range ramping of the mA signal from 4 to 20 to 4 mA while recording the 0-100-0% position, or the pressures applied that move the valve from 0-100-0%
• Stepping the mA signal on the input to the valve in steps and evaluating the valves response to the mA input changes
• Speed tests to determine how fast the valve can open or close
• Bump and partial stroke tests that help test valves over a portion of their range so they can be tested in a live process

ValveTrack™ Software enables further analysis and trending

Valve tests that are logged and recorded to memory in the 710 are available to upload to included ValveTrack™ analysis software.

ValveTrack™ software enables you to:

<ul">

• Upload, print and plot logged valve tests taken in the field
• Compare previous uploaded tests to recent tests
• View valve test history by HART Tag ID
• Export valve test data to CSV for additional analysis in Microsoft Excel®

Saving time, getting answers

In addition, the 710 offers:

• Logging of HART data in the field. Once recorded by the 710 in the field, the ValveTrack™ software can upload the HART configuration of up to (20) HART devices in your plant and output data in either (.csv) or (.txt) format.
• Data logged mA loop measurements and HART data can be recorded from a particular transmitter for troubleshooting and loop tuning. The data log feature offers selectable capture with recording intervals of 1 to 60 seconds and a logging capacity of 4910 records or 99 individual sessions. Each record contains the mA measurement and all four process variables.

Product Highlights

• Valve test procedures that deliver Good, Marginal or Bad assessment of a control valve
• Generic HART communication
• Best-in-class mA accuracy at 0.01 % measurement or source value
• Compact rugged design
• Intuitive user interface with Quick-Set knob for fast setup, easy to use
• 24 V DC loop power with mA measure mode (-25 % to 125 %)
• Resolution of 1 μA on mA ranges and 1 mV on voltages ranges
• Built in selectable 250 Ω resistor for HART communications
• Simple two wire connection for all measurements
• Auto shutdown to conserve battery life
• Variable step and ramp time in seconds

HART communication

The Fluke 710 offers a built-in HART modem to communicate the following HART commands:

• Read sensor PV information
• Read PV output information
• Read and write PV unit type, tag ID name, descriptor, and message
• Read and write PV ranges (upper and lower)
• Enter/exit fixed current mode
• Set zero offset
• Trim DAC zero (mA output 4 mA)
• Trim DAC gain (mA output 20 mA)

HART Commands for Valves

The 710 includes these unique HART commands to support control valves:

• Autotrim of valve controller

In addition, the Fluke 710 offers: 

• Logging of HART data in the field. Once recorded by the 710 in the field, the ValveTrack™ software can upload the HART configuration of up to 20 HART devices in your plant and output data in either .csv or .txt format
• Data-logged mA loop measurements and HART data can be recorded from a particular transmitter for troubleshooting and loop tuning. The data log feature offers selectable capture with recording intervals of 1 to 6 seconds and a logging capacity of 4910 records or 99 individual sessions. Each record contains the mA measurement and all four process variables.

ZAR -1

Fluke 719Pro Electric Pressure Calibrator

sku Product SKU:  FLK-719Pro

Fluke 719Pro Electric Pressure Calibrator sources, simulates, and measures mA signals and more

The 719Pro includes a full functioning loop calibrator that sources, simulates, and measures mA signals and more making it the ideal test tool for calibrating high accuracy transmitters, pressure switches, and pressure gauges.

Get the ultimate in measurement flexibility with the large backlit screen, which displays three parameters at once:

• Pressure measurement from an internal or external sensor
• Sourced/simulated or measured mA values
• Temperature measured by optional RTD probe

ZAR -1

Fluke 726 Precision Multifunction Calibrators

sku Product SKU:  FLK-726

Product overview: Fluke 726 Precision Multifunction Calibrators

Process calibration designed specifically for process industries

The Fluke 726 is a precise and powerful, yet easy-to-use, field calibrator. It features broad workload coverage, calibration power, and unsurpassed accuracy needed by process professionals. It measures and sources almost all process parameters to calibrate almost anything. Use it to test sensors and valves, and to test and calibrate transmitters. The 726 interprets results without the help of a calculator and stores measurement data for later analysis.

Measurement capabilities

Fluke 753

sku Product SKU:  FLK-753

Product overview: Fluke 753 Documenting Process Calibrator

Fluke 753 Documenting Process Calibrator helps you work smarter and faster

The Fluke 753 is a powerful multifunction documenting calibrator that lets you download procedures, lists, and instructions created with software, and upload data for printing, archiving, and analysis. You'll find it does the work of several tools, with simultaneous source and measurement capabilities for all common process parameters. It sources, simulates, and measures pressure, temperature, and electrical signals in one rugged, hand-held calibration tool. It also automates calibration procedures, captures data for documentation, and helps you meet rigorous standards like ISO 9000, FDA, EPA, and OSHA regulations.

Fluke 754 Documenting Process Calibrator-HART

sku Product SKU:  FLK-754

Product overview: Fluke 754 Documenting Process Calibrator-HART

Fluke 754 Documenting Process Calibrator with HART communication does the work of many tools

Whether you're calibrating instruments, troubleshooting a problem, or running routine maintenance, the Fluke 754 with HART® communication can help you get the job done faster. It does so many different tasks, so quickly and so well, it's the only process calibrator you need to carry. This rugged, reliable integrated communicating calibrator is ideal for calibrating, maintaining, and troubleshooting HART and other instrumentation.

The 754 is a power multifunction documenting calibrator that you can use to download procedures, lists, and instructions created with software; or upload data for printing, archiving, and analysis. The powerful built-in HART interface is capable of performing nearly all the day-to-day tasks you now perform with a separate communicator.

In fact, the 754 does the work of several tools. It sources simulates and measures pressure, temperature, and electrical signals with one rugged, hand-held device. For documentation, the 754 automates calibration procedures and captures your data. And, of course, it helps you meet rigorous standards like ISO 9000, FDA, EPA and OSHA regulations. Plus, the new improved graphical screen, Li-Ion battery for longer life, USB port, and accessories help you work smarter and faster.

To create a seamless/paperless calibration management system consider adding Fluke DPCTrack2 Calibration Management software for use with your Fluke 753 and 754 or even legacy Fluke 743 and 744 calibrators.

ZAR -1

Fluke 771 Milliamp Process Clamp Meter

sku Product SKU:  FLK-771

Fluke 771 Milliamp clamp meter saves you time by measuring 4-20 mA signals without breaking the loop

The Fluke 771 delivers all the basics. It measures 4-20 mA signals without "breaking the loop", allowing you to measure low level dc current while saving downtime and money. You can also use it to measure output signals from transmitters without breaking the loop when maintaining and troubleshooting process and automation equipment. This saves time and avoids disruption to the process. For more convenience, the detachable clamp can be attached to the wire you're testing while you move the meter—connected by the extension cable—to a better viewing position. This is especially helpful for taking readings in tight locations.

ZAR -1