-
by Leanne ColeFebruary 11, 2020
Fluke Pro, Jason Axelson explains why early identification of battery failure helps keep your assets as well as your company up and running.
Use a battery tester to measure voltage, internal resistance and strap resistance to find indications of early-stage battery failure or installation problems.
Key measurements – Internal battery resistance, dc and ac voltage, dc and ac current, ripple voltage, frequency and temperature.
Sequence measurement mode – Automatic or manual sequence testing of battery strings with automatic measurement storage including voltage, resistance, and temperature (with BTL21 intelligent test probe), eliminating the need to press a button each time measurement needs to be saved.
Comprehensive logging – All measured values are automatically captured during testing and can be reviewed on the instrument before downloading for on-the-go analysis.
451 Views
-
by Leanne ColeFebruary 3, 2020
Fluke Product Manager, Jessie Zhang, walks through when it is the right time to use a digital multimeter versus a clamp meter. The two products offer different features and should be used in different situations.
A digital multimeter is a test tool used to measure two or more electrical values—principally voltage (volts), current (amps) and resistance (ohms). It is a standard diagnostic tool for technicians in the electrical/electronic industries.
A clamp meter is an electrical test tool that combines a basic digital multimeter with a current sensor. Clamps measure current. Probes measure voltage. Having a hinged jaw integrated into an electrical meter allows technicians to clamp the jaws around a wire, cable or other conductors at any point in an electrical system, then measure current in that circuit without disconnecting/de-energizing it.
395 Views
-
by Leanne ColeFebruary 25, 2019
Bump testing gas detectors before each day’s use is the only way to be sure that the sensors respond to gas.
570 Views
-
by September 26, 2018
Step by step instructions on how to upgrade the firmware in your Radian Research RD-3x Standard.
www.radianresearch.com
813 Views
-
by September 26, 2018
Instructional video highlighting the current input locking connector for a Radian RD-2x or RD-3x Standard. This locking feature is design for safety and ease of use.
Website: www.radianresearch.com
744 Views
-
by September 26, 2018
How to connect the RB-10 Bantam Lite to a typical meter installation.
www.radianresearch.com
959 Views
-
by September 26, 2018
The RB-10 Bantam Lite remains unscathed as it falls from a SUV.
http://www.radianresearch.com
877 Views
-
by September 26, 2018
Radian demonstrates the durability of the RB-10 Bantam Lite by driving a SUV onto it.
http://www.radianresearch.com
850 Views
-
by September 26, 2018
The RM-17 is the only portable watthour test system to include a complete calibration report.
806 Views
-
by September 26, 2018
Instructional video illustrating the procedure to convert an older field test kit for use with the dytronic series of standards.
Website: www.radianresearch.com
Radian Research, Inc.
3852 Fortune Drive
Lafayette, IN 47905
575 Views
by Kai HiltonSeptember 29, 2017
MDO-2000E series is equipped with a dual channel 25 MHz arbitrary waveform generator.
We could utilize arbitrary waveform generator to output waveforms and conduct frequency domain analysis by the built-in spectrum analyzer.
1411 Views
Update Required
To play the media you will need to either update your browser to a recent version or update your
Update Required
To play the media you will need to either update your browser to a recent version or update your
Update Required
To play the media you will need to either update your browser to a recent version or update your
Update Required
To play the media you will need to either update your browser to a recent version or update your
Update Required
To play the media you will need to either update your browser to a recent version or update your
Update Required
To play the media you will need to either update your browser to a recent version or update your
Update Required
To play the media you will need to either update your browser to a recent version or update your
Update Required
To play the media you will need to either update your browser to a recent version or update your
Update Required
To play the media you will need to either update your browser to a recent version or update your
Update Required
To play the media you will need to either update your browser to a recent version or update your
Update Required
To play the media you will need to either update your browser to a recent version or update your
Fluke Pro, Jason Axelson explains why early identification of battery failure helps keep your assets as well as your company up and running.
Use a battery tester to measure voltage, internal resistance and strap resistance to find indications of early-stage battery failure or installation problems.
Key measurements – Internal battery resistance, dc and ac voltage, dc and ac current, ripple voltage, frequency and temperature.
Sequence measurement mode – Automatic or manual sequence testing of battery strings with automatic measurement storage including voltage, resistance, and temperature (with BTL21 intelligent test probe), eliminating the need to press a button each time measurement needs to be saved.
Comprehensive logging – All measured values are automatically captured during testing and can be reviewed on the instrument before downloading for on-the-go analysis.
Fluke Product Manager, Jessie Zhang, walks through when it is the right time to use a digital multimeter versus a clamp meter. The two products offer different features and should be used in different situations.
A digital multimeter is a test tool used to measure two or more electrical values—principally voltage (volts), current (amps) and resistance (ohms). It is a standard diagnostic tool for technicians in the electrical/electronic industries.
A clamp meter is an electrical test tool that combines a basic digital multimeter with a current sensor. Clamps measure current. Probes measure voltage. Having a hinged jaw integrated into an electrical meter allows technicians to clamp the jaws around a wire, cable or other conductors at any point in an electrical system, then measure current in that circuit without disconnecting/de-energizing it.
Bump testing gas detectors before each day’s use is the only way to be sure that the sensors respond to gas.
Step by step instructions on how to upgrade the firmware in your Radian Research RD-3x Standard.
www.radianresearch.com
Instructional video highlighting the current input locking connector for a Radian RD-2x or RD-3x Standard. This locking feature is design for safety and ease of use.
Website: www.radianresearch.com
How to connect the RB-10 Bantam Lite to a typical meter installation.
www.radianresearch.com
The RB-10 Bantam Lite remains unscathed as it falls from a SUV.
http://www.radianresearch.com
Radian demonstrates the durability of the RB-10 Bantam Lite by driving a SUV onto it.
http://www.radianresearch.com
The RM-17 is the only portable watthour test system to include a complete calibration report.
Instructional video illustrating the procedure to convert an older field test kit for use with the dytronic series of standards.
Website: www.radianresearch.com
Radian Research, Inc.
3852 Fortune Drive
Lafayette, IN 47905
MDO-2000E series is equipped with a dual channel 25 MHz arbitrary waveform generator.
We could utilize arbitrary waveform generator to output waveforms and conduct frequency domain analysis by the built-in spectrum analyzer.